fr1601g ? fr1607g t o -220a 1 o f 2 ? 20 00 w on- t op e l e c t ron i cs fr1601g ? fr1607g 16a fast recovery glass passivated rectifier features ! glass passivated die construction b ! fast switching ! high current capability c ! low reverse leakage current ! high surge current capability g a ! plastic material has ul flammability classification 94v-o pin1 2 d mechanical data f e ! case: molded plastic ! terminals: plated leads solderable per p mil-std-202, method 208 ! polarity: see diagram i ! weight: 2.24 grams (approx.) l ! mounting position: any h ! marking: type number pin 1 + + j pin 2 - case k maximum ratings and electrical characteristics @t a =25c unless otherwise specified single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. characteristic symbol fr 1601g fr 1602g fr 1603g fr 1604g fr 1605g fr 1606g fr 1607g unit peak repetitive reverse voltage working peak reverse voltage dc blocking voltage v rrm v rwm v r 50 100 200 400 600 800 1000 v rms reverse voltage v r(rms) 35 70 140 280 420 560 700 v average rectified output current @t c = 105c i o 16 a non-repetitive peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) i fsm 250 a forward voltage @i f = 16a v fm 1.3 v peak reverse current @t a = 25c at rated dc blocking voltage @t a = 125c i rm 5.0 100 a reverse recovery time (note 1) t rr 150 250 500 ns typical thermal resistance junction to case r jc 3.0 k/w operating and storage temperature range t j , t stg -65 to +150 c note: 1. measured with if = 0.5a, ir = 1.0a, irr = 0.25a. see figure 5. wte power semiconductors to-220a dim min max a 14.9 15.1 b ? 10.5 c 2.62 2.87 d 3.56 4.06 e 13.46 14.22 f 0.68 0.94 g 3.74 ? 3.91 ? h 5.84 6.86 i 4.44 4.70 j 2.54 2.79 k 0.35 0.64 l 1.14 1.40 p 4.95 5.20 all dimensions in mm
0 4 8 1 2 16 0 25 50 75 100 125 150 175 i , average forward current (av) t , c as e temper a tur e ( c ) fig . 1 , t ypica l forwar d curren t deratin g curve c 0.1 1 10 2 0 100 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 i , instantaneous forward current (a) f v , instantaneous forward voltage (v) fig. 3, typical instantaneous forward characteristics f t = 25 c pulse width = 300 s 1% duty cycle j m 0 1 25 2 5 0 3 75 1 1 0 100 i , peak forward surge current (a) fsm number of cycles at 60hz fig. 2 max non-repetitive peak surge current 8.3ms single half sine-wave jedec method 1.0 10 100 1000 1.0 10 100 c , capacitance (pf) j v , reverse voltage (v) fig. 4 typical junction capacitance r t = 25 c f = 1.0mhz j 50v dc approx 50 ni (non-inductive) w 10 ni w 1.0 ni w oscilloscope (note 1) pulse generator (note 2) device under test t rr se t tim e bas e fo r 5 /10 ns/cm +0.5a 0a -0.25a -1.0a notes: 1. rise time = 7.0ns max. input impedance = 1.0m , 22pf. 2 . ris e t im e = 10n s max . inpu t impedanc e = 5 0 . w w fig. 5 reverse recovery time characteristic and test circuit (+) (+) (-) (-) fr1601g ? fr1607g t o -220a 2 of 2 ? 20 00 w on- t op e l e c t ron i cs
|
